I recently had someone email me that had purchased our 8 day course (we sell as an illustrated booklet for those that are in a hurry to make a decision).
He asked this question: "How does your system "tune"? I plan on purchasing your kit with tuner, but don't understand what I am tuning."
That's a great question. I figured others might have the same one, so this is how I answered it:
The “tuners” we provide, don't directly affect the flow of fuel, we rely on the massive work of the engineers who programmed the engines with specific fuel maps, based on the engines needs, to do that.
All engines with computers (ECM's) use sensors to gather data and send that to the ECM. The ECM then chooses the proper fuel map, based on that information, which is constantly changing. Most "TUNERS" try to inject their own programs to help the engine get more horsepower or economy, but many times the ECM will override their attempts (especially when it comes to gas savings!)
So our tuners bypass the programming entirely, and "hijack" the signal before it gets to the ECM. We actually route the signals coming from the O2 sensors and MAF/MAP sensors, before they reach the car computer (ECM). While it seems “that is not enough”, the sensors are quite sensitive to changes internally in the engine, and just a few millivolts of change affects WHICH fuel map the ECM decides to use, which determines how much fuel to inject. In other words, we are not trying to work against the engineering software of the car, we are simply changing the inputs that determine how much fuel is used. We can adjust the MAF (in most cars) to actually cause the engine to stumble because the fuel is leaned out by the ECM, based on those signals. So while we are only adjusting or tuning the signals by using a voltmeter, we are leveraging the car computer to do the rest of the work.
Does that make sense? Obviously, it is much more complex than that, but essentially, computers are only as smart as the data that is input into them. We make sure they get the right data to lean out the fuel in an unconventional way.
Hope that helps...
Bob
Make sure you check out our cutting edge new H2XTRME HHO generators, and check out more info on the tuners as well!
Bob
The amount of money saved by burning your fuel more efficiently using the on- demand hydrogen-oxygen our kits inject, is determined by a couple of factors:
1) How big is your engine? Let's say you are getting 15 miles per gallon now, You could get 23 mpg with our kit (a 53% increase). I did that with my Chevy Trailblazer. Instead of filling up every 4 days, you could go 6 or 7 days on the same tank. Instead of filling up 7 times a month, now you fill up just 4 times, for example. You could save 3 tanks of gas every month! Smaller engines would do even better.
3 Tanks of gas = 3 x 15 gallons x $5.00 per gallon = $225 SAVED every month.
2) How much do you drive? If you only take the car out on Sunday, and never go anywhere, you should not buy the kit unless you are really concerned about the emissions (see this chart for actual reductions).
If you drive every day to work and back, and use it every day, obviously you are going to have much higher savings!
3) How well do you maintain your car? A tuned up car with clean oil and air filters will always give best results. If your car is belching oil, we can still help clean up the exhaust, but your results may not be as high as a well maintained car.
4) How good of an installation did you do? We give a very detailed installation manual that lays everything out clearly on how to install, set up and run your HHO kit for maximum results. Clean distilled water is a must, and your amps should be at recommended setting. If your car has fuel injection, you must use our gas or diesel tuners and adjust as we instruct for best results.
Once you experience the increased response of your car, the instant acceleration on passing or on the hwy, the clean and quiet running engine, you will never want to turn it off again, and you be smiling every time you pass up the gas station with it's long lines and outrageous prices!
In Part 1, we talked about the basics of fuel injection, how they work and why you need an EFIE or Diesel chip with an HHO kit on a modern car.
We talked about how injectors are controlled by the cars computer (ECM) to determine how long they stay open or closed, and how fast they open or close. The ECM decides those parameters using a programmed set of "fuel maps", that utilize the information from the cars sensors to determine if the engine needs more gas or less gas.
Computers can only do what they are programmed for. They can't tell if you are going up a hill or towing a trailer, or anything else, without reading the information from the sensors first. The two key sensors are the O2 sensors in the exhaust to monitor oxygen levels, and the MAF or MAP sensors that monitor the flow of incoming air and the manifold vacuum.
The sensors transmit the data to the cars ECM using very tiny millivolt signals. An O2 sensor may be in the 400 millivolt range for example. When you install one of our EFIE's, you use a volt meter to adjust that millivolt rating down to say 300 millivolts. By doing this, you are telling the car computer to "Lean Out" the fuel, which allows the HHO generator to supply the additional energy, and still save fuel (If you do this without adding an alternative fuel, you will notice a lack of power, and could even burn your valves, so ONLY do this when injecting a new fuel like HHO gas). AN efie gas tuner allows you to slowly tweak and test to get the optimum performance from your hho generator.
The MAF sensor works on the same premise, but measures the mass air flow going into the engine to determine the work the engine is doing (engine load). When you use our EFIE or Diesel Chip, you adjust them to reduce the engine load setting. In other words, you are telling the car computer that it has a 20% lighter engine load than it actually is (for example). The computer then reduces fuel because of that.
It is not as complicated as it may seem at first. You simply locate the one signal wire on a sensor and connect it to our EFIE or Diesel Chip, then adjust it with a screwdriver. After that, you never mess with it again. (we show you how to locate the wire, install it and adjust it in our free manual).
By changing the signals ever so slightly, you are teaching the car computer how to reduce the gas or diesel usage, when supplemented by pure hydrogen and oxygen gas. That is the Long term way to make your hho kit function as both an emission reducer and fuel saver, without loss of power or performance.
Stay tuned for Part 3 where we get into the Pro series level chips and how they differ from our advanced series.
If you have any questions- feel free to email us!
Until next time,
Bob
This question is one of the most argued points when it comes to HHO generator kits on vehicles, so I thought it would be a good idea to go ahead and address the issue.
An EFIE stands for Electronic Fuel Injection Enhancer, and it was really invented back many years ago by a man named George Wiseman, who then shared it with the world to use as necessary to help cars with fuel injection work well with HHO boosters. The file was quickly shared all over the internet and became the standard for most EFIE's still in use today, though they have been vastly improved, and operate smarter (like in our advanced EFIE designs).
The tuner circuits were invented as a response to the advancement in car computer enhancement, and the advent of throttle body Injection (TBI), and Fuel Injection Rails to inject metered amounts of fuel into a cars engine. They solved a huge amount of problems that commonly occurred with carburetors, such as hard starting, vapor lock, stalling, rough idle, etc.
The fuel injector contains a small valve that opens and closes rapidly to allow a fast, fine mist of gasoline or diesel to be injected into the combustion chamber of the engine at the perfect time, in the perfect amount, based on the circumstances of the car engine (ie: the car may be idling, accelerating, decelerating, going uphill, towing a trailer, etc), and each circumstance requires a different response from the injectors to vary the fuel properly. The programming used to determine these conditions is put together in a series of "Fuel Maps", that have pre-designated timing sequences for the injectors.
The injectors are actually an incredible invention. Think of them as a miniature high pressure spray gun, that not only opens and closes in micro seconds, but with the computer programming, they are told to pulse faster or slower, and stay open faster or slower depending.
So what determines their pulse rate and timing? The computer programming. But how does the computer know what to tell the injectors? Only ONE way...through the engine sensors. The computer has No Other Way of knowing the condition of the engine. Without the sensors, it would be like a blind man trying to run a race in a country he had never been, having no idea what is around the next corner.
THAT is where the EFIE comes into play!
Stay tuned for Part Two where I will get into the sensors of the engine that control, and how the EFIE affects them, and why they are necessary for long term gains when using an HHO kit
This is another commonly asked question we get quite often when people are just finding out about hho and the on demand hydrogen world.
The short answer is - Yes!
The long answer: Because our kits create a unique form of hydrogen-oxygen gas, (which is very energetic, and very combustible when ignited inside an engine), the HHO gas will work on any working engine that burns hydrocarbon fuel already. So it will work in all engines currently using gasoline (petrol), diesel, bio-diesel, CNG (Compressed Natural Gas), and LPG (Liquid Propane Gas).
One of our customers driving an LPG conversion Lorry in the UK, got a 50% increase in mileage when he added our hho kit to his vehicle!
If you have an newer vehicle using gasoline, you need an efie/maf tuner for the electronics, which you can see here: http://www.hhokitsdirect.com/collections/all/products/efie-maf-advanced-gas-tuner-for-hho-kits
If your newer vehicle uses diesel or bio-diesel, You will need the Diesel tuner here: http://www.hhokitsdirect.com/collections/all/products/advanced-diesel-tuners-for-hho
If your car is older and still uses a carburetor, or mechanically controlled diesel pump, then the hho kits work fine without tuner chips at all.
If you still need help- feel free to email us through the contact form on our site, or with Live Chat during normal business hours (MON-FRI; 9 am - 5 pm)