Partial HHO Generator Kits
|
 "THE WORKS" HHO Full Installation Kit
NOTE: This is NOT for the build it yourself book- this is for those that already have a working hho generator and are ready to install it. For a complete kit that has everything described in my build it yourself manual, go here: Build it Yourself kit (NOT the Hybrid Cell).
If You have been building your own system or bought our BARE HHO Generators and and are frustrated with available parts or don't have time to hunt down your own supplies to install it, then use our HHO installation kit that comes complete with everthing you see here. The 3 Quart reservoir comes pre-drilled and tapped for fittings (included in kit). Bubbler is assembled and ready to fill. |
- Reservoir/Cap
- Bubbler
- 10' Hose
- 60 amp Fuse Holder
|
- 2 - 40 amp fuses
- 20' - 10 Gauge Wire
- 20' - 16 Gauge Wire
- 60 Amp Gauge
|
- Solenoid Check Valve Kit
- 70 Amp Continuous Relay
- 2.7 oz. Electrolyte
- 2 -"Y" Fittings
|
- ON/OFF Manual Switch
- Elbow fittings
- Mounting Straps
- Misc Bolts/Nuts
|
|
 HHO ELECTRONICS UPGRADE KIT
IF you have installed a Brute Force HHO Generator and would like to upgrade to an Electronics Controlled System, then you need our elctronics upgrade kit that comes with 20' of 10 Gauge wire, 8- slide terminals for connecting to the PWM, 4 3/8" ring terminals for your HHO Generator, and a 30 AMP HEAVY DUTY PWM (Pulse Width Modulator).
|
 Heavy Duty 3 Quart HHO Reservoir
HHO Reservoirs for your electrolyte are the best solution to reducing the maintenance of water refills for HHO Generators. This heavy duty 3 Qt. System can be filled 2/3 with electrolyte and fit into your HHO kit installation. It is manufactured with extra deep fitting shoulders - 2 on top and 1 on bottom for your fittings. We PRE-DRILL and TAP them for you - ready for your 3/8" fittings or you can buy ours. We include a 4th hole (for a 1/4" npt fitting) drilled and tapped in the top for either our unique solenoid check valve system or your own vacuum/pressure relief system. |
 
Heavy Duty Clear Bubbler
This new Clear Body Bubbler is available to buy separately for the first time (usually only available in our kits). Everything is constructed from high quality clear PVC (1/4" thick walls), and ABS caps. All fittings are drilled/tappped and glued into place for you- ready to fill and use. The red dot is the "OUT" fitting- just attach the hose from there to your intake. Comes with a PRV rubber stopper for quick filling and pressure relief if you ever have a flashback.
|
 SOLENOID CHECK VALVE KIT FOR HHO
This Solenoid Check Valve kit is designed for our Heavy Duty Reservoirs and included in all our complete HHO kits. The elbow fitting screws into reservoir and connects via included hose to check valve. 16 gauge wire is included to conect valve to your relay or a fuse. When HHO Generator is working valve is closed except a small bypass inlet (preventing high vacuum from engine collapsing reservoir), when engine and HHO generator are turned off, the solenoid check valve fully opens allowing fresh, outside air in to the reservoir to prevent collapse as expnaded gases cool and contract inside. Best system out there to deal with cool down. ALSO prevents reservoir from sucking out the water from a secondary bubbler |
 NYLON MINI KIT
We put together this Nylon mini kit because a lot of people have trouble finding just these few items- the nylon threaded rod, washers and jam nuts (thinner than regular nuts). Included are 2 - 3.75"-18 nylon rods, 16 nylon washers (1/16' thick), and 20 Stainless Steel Jam nuts. These are recommended sizes for use in the Build Your Own HHO Kit instruction manual. |
 ABS CONTAINER PARTS
Some people have trouble finding the ABS Container Parts used in the HHO Generator I teach how to build in my book.Many stores in different parts of the country don't carry them and some countries just don't have them at all. I decided to add these to our inventory- they will make the HHO Power Cell and Bubbler. These are 4" ABS tubes and fittings for the hho generator container, and 2" ABS with end caps for the bubbler assembly. Everything is cut to proper length and ready for you to assemble. |
| |
|
|
|
